Frequency dependence of plasma characteristics at different pressures in cylindrical inductively coupled plasma source

The effects of driving frequency on plasma parameters and electron heating efficiency are studied in cylindrical inductively coupled plasma (ICP) source. Measurements are made in an Ar discharge for driving frequency at 13.56/2 MHz, and pressures of 0.4–1.2 Pa. In 13.56 MHz discharge, higher electron density (n_e) and higher electron temperature (T_e) are observed in comparison with 2 MHz discharge at 0.6–1.2 Pa. However, slightly highern_e andT_e are observed in 2 MHz discharge at 0.4 Pa. This observation is explained by enhanced electron heating efficiency due to the resonance between the oscillation of 2 MHz electromagnetic field and electron-neutral collision process at 0.4 Pa. It is also found that the variation ofT_e distribution is different in 13.56 and 2 MHz discharge. For ICP at 13.56 MHz, T_e shows an edge-high profile at 0.4–1.2 Pa. For 2 MHz discharge,T_e remains an edge-high distribution at 0.4–0.8 Pa. However, the distribution pattern involves into a center-high profile at 0.9–1.2 Pa. The spatial profiles ofn_e remain a center-high shape in both 13.56 and 2 MHz discharges, which indicates the nonlocal kinetics at low pressures. Better uniformity could be achieved by using 2 MHz discharge. The effects of gas pressure on plasma parameters are also examined. An increase in gas pressure necessitates the rise ofn_e in both 13.56 and 2 MHz discharges. Meanwhile, T_e drops when gas pressure increases and shows a flatter distribution at higher pressure.     

负径向电场对带电粒子俘获率影响的数值模拟

本文采用数值方法求解Grad-Shafranov方程反演EAST典型长脉冲放电实验(炮号33068)的平衡位形和磁场分布，进而结合粒子在托卡马克电磁场中的运动方程，模拟氘离子在负径向电场存在时的运动轨迹，并统计不同负径向电场下的氘离子俘获率。结果表明：随负径向电场的增大，氘离子轨迹由扩张通行轨迹向外翻香蕉轨迹再向内翻香蕉轨迹，最后向压缩通行轨迹演变；氘离子俘获率随负径向电场的增大而减小，氘离子初始速度越小，其变化越大。     

Heating frequency optimization for artificial field-aligned scattering

In this study, we present a simulation study of artificial field-aligned irregularities (AFAI) to calculate the scattering coefficient considering a Gaussian autocorrelation function for the wave number spectrum of the density fluctuation. By analyzing variations in the scattering coefficient under different ionospheric backgrounds, the optimal range of the heating frequency was found, which is about 0.9–1 times the critical frequency of the F2 layer. This is especially noticeable as when the heating frequency varies from 0.5 times to 0.9 times of the critical frequency, the scattering coefficient increases by 6.8–16.2 dB. These results should be useful for optimizing the heating frequency in the future artificial field-aligned scattering (AFAS) transmission applications at middle and low latitudes.     

Design of switchable band‐notched frequency selective absorber

An active band‐notched frequency selective absorber (BNFSA) with switchable notch band is proposed in this article. The BNFSA is a two‐layer structure composed of a lossy layer at the top and a ground plane at the bottom, separated by an air spacer. The element of the lossy layer is a lumped‐resistor‐loaded metallic dipole with a parallel LC resonance structure, which is realized by complementary n‐shaped resonator (CnR) inserted in the center, and PIN diode is welded at two arms of CnR. The bias circuit printed on the back of the substrate of the lossy layer connects to anode and cathode of the diode by via hole and isolates by the inductor. Simulation results show that the notch bands are located at 4.50 and 6.81 GHz when the diode sets to ON and OFF, respectively. To validate the performance of switchable BNFSA, the prototypes are fabricated and measured, reasonable agreement between simulated and measured results is obtained.     

Electromagnetic torque detecting for optimization of in-mould electromagnetic stirring in the billet and bloom continuous casting

ABSTRACT

In this paper, an electromagnetic torque device based on the theoretical model was established to determine the optimum frequency accurately and conveniently in billet and bloom continuous casting with in-mould electromagnetic stirring (M-EMS). Magnetic characteristics with M-EMS was investigated by numerical simulation and physical experiment with the application of electromagnetic torque device and gauss meter. In addition, the effects of stirring frequency with M-EMS on macro segregation and equiaxed crystal ratio were compared and analysed for 55SiCr with 150?mm?×?150?mm billet caster and BU with 310?×?360?mm bloom caster by a series of plant trials, respectively. The results showed that maximum magnetic flux density and maximum electromagnetic torque occurred with different frequency and same current in M-EMS, and central equiaxed crystal ratio and macro segregation has been significantly improved by optimum frequency with M-EMS.     

Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.     

Enhanced electrical and photoluminescence properties of BiSbO4-doped CaCu3Ti4O12 ceramics by modifying grain boundary response

CaCu₃Ti₄O₁₂-xwt%BiSbO₄ ceramics (CCTO-xwt%BSO, x = 0, 1, 2, 3) were prepared by solid-state reaction method. The microstructure, dielectric properties, varistor properties, photoluminescence properties of CCTO-xwt%BSO ceramics were studied in this work. Results showed that all samples formed CaCu₃Ti₄O₁₂ (CCTO) single phase. Doping BiSbO₄ (BSO) restrained the abnormal grain growth and increased the grain boundary density of ceramics. The introduction of BSO led to the increase of the grain boundary resistance, reducing the dielectric loss and enhancing the temperature stability of dielectric properties. The nonlinear electrical characteristics are enhanced with proper concentration of BSO. And the improved varistor performance with breakdown electric field of ～3.98–34.6 and nonlinear coefficient of ～1.49–2.96 are obtained for CCTO-xwt%BSO samples. In addition, the photoluminescent emission of the samples is enhanced with the addition of appropriate equivalent BSO, showing the potential applications in novel devices with photoluminescent/electrical multifunctional properties.     

Excellent destabilization effect and ideal desorption temperature in the hydride Mg2FeH6 substituted with yttrium; a first principles study

We investigated some properties of the hydride Mg₂FeH₆ substituted with yttrium by a first principles calculation. Some experimental results showed that 4d transition metal, yttrium serves as a good catalyst for magnesium based hydrogen storage alloys, but there are a few theoretical studies about magnesium based hydrides substituted with it. Mg₂FeH₆ is regarded as a cheaper material than pure MgH₂, while it is crystalized into Fm3m structure (space group 225). Although it has high hydrogen storage capacity, many investigations have not been devoted to it due to its extremely high thermodynamic stability. The yttrium substituted Mg₂FeH₆ exhibits very low energy of formation, and its desorption temperature, 75 °C is very suitable for practical hydrogen storage applications. Our results showed that Mg₂FeH₆ is destabilized effectively by yttrium substitution and introducing vacancy defects has additive effect to the improvement of dehydrogenation performance.